Let There Be Light!
Improve your Pontiac’s lighting system and avoid potential fire damage by replacing its harness.
Story and photography by Jim McGowan
Any Pontiac enthusiast who owns a 40-year-old Poncho is familiar with the many and varied problems that come with that age.
No, we’re not talking about a larger belt size, but rather things like dry, cracking and peeling engine compartment wiring.
Heat, chemicals and other underhood factors can cause the once supple wires to deteriorate to the point of being dangerous. Many an engine compartment fire has been the result of worn wiring shorting out and flaring up, or old wires becoming hot and causing the shielding to melt or burn, leading to a fire. The original factory wiring was still powering the engine and front lighting of our resident ’70 Judge project car, and we were no longer willing to take a chance on having a catastrophic failure. We have already replaced the engine harness in a previous article (PE, January 2010), and now will tackle the lighting harness.
In the old days, replacing the harness would have required either finding a factory replacement, or recreating your own, wire by wire. While the wire-by-wire method might be good for learning electronics and wiring, it’s not a fun or easy task.
The forward lamp harness (#13635) that we installed fit precisely, requiring no cutting or soldering. It’s literally a “Plug and Play” installation. Simply remove the old harness and install the new one. But, of course, it’s not quite that simple, so we’ll show you what is required for the replacement in this 1970 model GTO Judge, but most other Ponchos will be similar.
No special tools are required, but you’ll be doing some parts disassembly to access the required work areas. It’s a good idea to take digital photos of the disassembly so you have a reference for putting things back together. Pay particular attention to which plugs go to which lights, as they are different, and you’ll be using a small spade connector from the original turn signal socket, which needs to be transferred to the new harness. That is illustrated in the photo sequence. If possible, have a factory assembly manual available for reference.
Since you’ll be taking apart some of the front end bright work, it’s a great time to do a little detailing of these parts and the areas behind the front grilles, too.
1 Here’s the new harness ready for installation. The harness contains connections to all four headlights, the turn signals, two ground wires, the dual horns, the side marker lights and the bulkhead connector. There is also a connector to the brake fluid distribution block on the frame rail and another to the horn relay.
2 We begin by removing the front cowl air dam from the core support. We’ll use this top access to get at the grille mounting points and the wiring across the front of the car.
3 Continue disassembly by removing the four bolts securing each of the front grilles and removing them. You’re now reaching down into the area previously covered by the air dam.
4 Here’s the original factory lighting harness. The car was disassembled years ago for paint, and the body shop guys never returned the harness to its proper location in the clips under the core support.
5 In the top center of the photo is one of several harness clips that should be used to secure the new harness. We will use all of these for the reinstallation.
6 Now remove the bezels surrounding all four headlights and then the bulb retaining rings, which are secured with three small screws – don’t lose them.
7 The headlight bulb and wiring can now be pulled forward. Check out which harness plug is used on each light and the location and number of the bulb. If you reinstall them wrong, the main headlight bulbs could end up in the inside position. Take pictures or make a diagram and notes as needed.
8 This side view of the crossmember support shows the original harness as it passes through a curved area in the support; you must use the same routing as the factory due to the length of the harness wiring.
9 Under the front of the driver’s side fender, at the core support, is this small plastic baffle. It is pressure fit into the core support and covers the access hole through which you will pass the wiring harness and all connectors. A slit in the top allows you to remove it and replace it on the new harness. The original harness and ground wire are visible in the rear.
10 After unplugging all the lamp connectors, and disconnecting the ground wire, the original harness is now being removed from the passenger side through the access area in the center core support. We’re working from the passenger side to the driver’s side.
11 Here’s the original harness removed from the front, but still connected at the bulkhead. Do not throw this harness away. There are two connectors you’ll need still in it, plus if you ever need factory connectors in the future, it will come in handy. Leave it connected at the bulkhead for now.
12 Snake all the connectors and new wiring through the access hole in the core support and route them to the correct areas using the same path you used to remove the old harness. Let the plugs hang out of the correct bulb sockets and check your photos to make sure they are right.
13 This is the bulkhead connector. It is to the right of the master cylinder. If your car has a power booster, accessing the connector is more difficult due to space limitations, but you can do it. We marked the wires to the horn relay with tape to make sure everything was properly connected. The tan wire goes to the brake distribution block.
14 The ground wires are fairly easy to disconnect, but trying to route the new wire back in place is tough. Use an alligator clip style wire, snaked through the hole under the fender and down to the headlight bucket. Connect it to the ground wire and pull up through the access hole. You can then connect it.
15 Here’s the alligator connector wire, still attached to the ground wire, which made this almost impossible routing a success. These are available from hardware stores, Harbor Freight, etc.
16 While the underside of the core support is a little grungy, all the factory harness clips were still in place and useable. Our new harness is now suspended as original.
17 Since we started installing all the wiring at the front, the bulkhead plug is not yet wangled through an access area in the driver’s side core support bracket, and then up to the access hole at the top of the panel. This takes a little patience, but will work.
18 The complete harness is now hanging in the support brackets under the core support with all the various plugs connected. It is important to have the wiring up high to prevent damage from road junk or minor collision damage. Make sure to connect the horn wiring!
19 The bulkhead connector has been passed through the access opening and now can be routed across the fender and to the connector area on the firewall.
20 Here you see the pressure fit panel back in place with the harness passing through it. You can also see the ground wire connected to the core support. This connection location is the same for both ground wires. Make sure you have cleaned the metal for a good ground.
21 Here’s the bulkhead connector removed from the firewall. It is secured with one bolt and contains the engine compartment connections on one side and the lighting harness connections on the other. The two plugs slide together to form the complete unit. Install the lighting harness connector as the original and carefully replace it on the firewall.
22 Here you can see the harness in the fender well clips, the bulkhead connector in place and the horn relay wiring connected and under the factory cover. But we’re not done!
23 It’s a perfect time to detail and polish any bright work items you have removed. These parts take a beating during normal driving, but will last for years if cared for.
24 Here’s a tip for reinstalling the headlight retaining rings: Those three little screws are difficult to install by hand. Insert the screwdriver into the screw head and wrap a small piece of masking tape around the screw head and screwdriver shaft. Then you can carefully insert the screw attached to the screwdriver in the hole and start the threads.
25 Before putting everything back together, connect the battery and turn the lights on. When we turned on our headlights, the turn signal bulbs didn’t light.
26 We removed the lenses and checked the bulbs and compared the old and new sockets. The small spade connector shown here must be removed from the old socket and installed into the corresponding slot in the new harness socket. If you don’t do this, your turn signal lights won’t work, either. Ours do now! n
(#13635) does not come up at Year One. Where can I find it and how much does it cost?ReplyDelete
tiffany and co outletReplyDelete
nike air max
adidas pure boost
nike flyknit racer
hollister clothing store
ray ban outlet
kate spade bags
nike cortez white
coach outlet online
air force 1
michael kors handbags
stephen curry shoes
michael kors handbags outlet
oakley sunglasses outlet
coach outlet online
coach outlet store online
louis vuitton outlet
fitflops sale clearance
pandora jewelry outlet
yeezy boost 350 black
rolex replica watches
cheap ray bans
michael kors outlet
michael kors outlet onlineReplyDelete
discount oakley sunglasses
cheap basketball shoes
true religion outlet store
nba jerseys wholesale
louis vuitton bags
michael kors outlet online
ralph lauren outlet
louis vuitton borse
tory burch outlet online
michael kors outlet online
michael kors outlet canada
burberry outlet online
moncler outlet store
coach factory outlet online
nike air max 90
cheap ray bans
cheap nike air max
mont blanc pens outlet
adidas supercolor pink
oakley sunglasses outlet
black timberland boots
coach outlet store
cheap oakley sunglasses
yeezy boost 350 balck
coach outlet online
nike shoes for cheap
coach factory outlet
prada sunglasses wholesale
adidas pure boost black
new balance shoes
louis vuitton handbags
Michael Kors Handbags On Sale,ReplyDelete
You can find Michael Kors handbags in many department stores around the country.
Michael Kors Purses Outlet,
They are being seen all over the place.
Michael Kors Bags On Sale,
There are so many fabulous handbags to fall in love with.
To find these amazing handbags you can also shop online for all your Michael Kors products.
تابلو بک لایت
This article is really contains lot more information about This Topic. We have read your all the information some points are also good and some professional writing services usually are awesome. business Logo Design Great post I would like to thank you for the efforts you have made in writing this interesting and knowledgeable article.ReplyDelete
یکی از مهم ترین دلیل گرانی در بازار فولاد، دلالی است که باعث شدهReplyDelete
قیمت ورق سیاه و
قیمت میلگرد نیشابور افزایش پیدا کند و گران شود.
Thanks for the best share and i loved it.ReplyDelete
cinema hd download free
An online search for Delhi Escorts is a perfect way of making sure that you will receive a popular type of Hot Escorts service.ReplyDelete
You have a real ability for writing unique content. I like how you think and the way you represent your views in this article. I agree with your way of thinking. Thank you for sharing.
Free online Bubble SHOOTER games
Thanks for the best one and i loved it,ReplyDelete
If you Learn how to set up and manage your Email account. AT&T has you covered with AT&T Mail support, So here is bellsouth email support number for your help.ReplyDelete
Bellsouth Email Support Number
Bellsouth Email Support
The worlds only remain those who stand in the long run. Every business needs various strategies to stand in the long run. The leading logo design agency in USA has an expert team of developers and designers that give the best clues and ideas to keep your business glowing for long runReplyDelete
Every time you complete the Bwwlistens.Com Within 48 Hours, you will grab a chance to win a $5 Off $25 Coupon to enjoy a free treat.ReplyDelete
Thanks For the Information.Excellent Writing and Easy to Understand.ReplyDelete
Some of the fast-food restaurant chain’s most popular breakfast dishes include the Whataburger Breakfast Menu 2022 Taquito with Cheese, Honey Butter Chicken Biscuit, and Egg Sandwich.ReplyDelete
This is the first time that I visit here. I found so many exciting matters in this particular blog, One thing I would like to request you that pls keep posting such type of informative blog.ReplyDelete
Clickbait 2021 Pia Brewer Jacket
Studentvue Tolleson LoginReplyDelete
Trying to check your grades on Studentvue Tolleson Login in Tolleson Union High School District? Tired of the poor layout and lack of features of the TUHSD Studentvue Tolleson Login app?
Shell Account Gas Login then check here Shell Account Gas Login Official portal.How to Air Gas Login Step-by-Step GuideReplyDelete
This is vert innovative blog! its the best post for this topic and very useful for beginners. I hope you will update more unique post, well done....ReplyDelete
divorce laws in new jersey
Spas are well-known all over the world for their unique treatment regimens and procedures visit body to body massage spa near meReplyDelete
For example, couples massages, monthly memberships, group packages or packages for groups. Encourage your customers to use these specials to save money while receiving a more complete spa experience. For more info: - Massage near meReplyDelete
Female to male massage spa near me is a form of massage in which a female masseuse provides massage therapy to a client who is male.ReplyDelete
Thanks for sharing beautiful content. I got information from your blog.keep sharingReplyDelete
strangulation charge in virginia
Strangulation Charge VA